Homeowner guide · Window replacement
How Window Replacement Works, From Measuring to Install Day
Window replacement looks simple from the outside: old window out, new window in. The parts that decide how it turns out happen before install day, when the openings are measured, the method is chosen and the order is written. Here’s the whole process, step by step, so you know what to expect and what to ask.
Step 1: The first conversation
It starts with a call, a text or an online booking. Have a rough list ready: which windows, what’s wrong with each, and roughly when the house was built. The build year matters because paid window replacement in a home built before 1978 falls under federal lead-safe work rules.
Window replacement in Columbus, OH
New windows, from one opening to the whole house.
Step 2: The visit and the measurements
Replacement windows are made to order, so the measurements are the foundation of the job. A careful measure includes:
- Width at three points (top, middle and bottom) and height at three points (left, center and right). Old frames are rarely perfectly square, and the smallest measurement usually governs.
- Diagonals, to see how far out of square the opening is.
- Sill angle and depth, so an insert sits correctly on the existing sill.
- Frame condition, probing sills and jambs for soft wood and looking for water stains inside and out.
The visit is also when code and safety questions come up:
- Bedrooms: whether each sleeping room has a window that works as an emergency escape opening. See our egress guide.
- Safety glass locations: the Residential Code of Ohio treats some window glass as a hazardous location that needs safety glazing, such as large panes with a bottom edge less than 18 inches above the floor near a walking surface, and glass facing a tub or shower with its bottom edge less than 60 inches above the standing surface, subject to the code’s conditions and exceptions.
- Historic district review, if the house is in one of Columbus’s local districts.
Step 3: Choosing the window and the method
With measurements in hand, the decisions are:
- Insert or full-frame for each opening. Our insert vs. full-frame guide covers this.
- Style, such as double-hung, casement, sliding or picture.
- Frame material. See frame materials compared.
- Glass package, including Low-E coatings, gas fill and double or triple panes, checked against the ENERGY STAR criteria for your county.
- Options such as grilles, hardware finish, screens and exterior color.
Step 4: The quote
A1 Windows gives you the price before work starts. Whoever you hire, a useful quote spells out:
- Each opening, with its size, style, material and glass package.
- The installation method for each opening.
- Interior and exterior trim work, including any exterior wrapping.
- Removal and disposal of the old windows.
- How lead-safe work practices will be handled in a pre-1978 home.
- Anything excluded, such as painting new interior trim or repairing rot found once the old frame is out, and how such findings will be priced.
Step 5: Ordering and the wait
Once you approve the quote, the windows are ordered to the measured sizes. Manufacturing time varies by product, size, color and season, so ask for the expected timeline when you order rather than assuming. A final check of measurements before the order is placed is worth the extra visit on unusual openings.
If a window can’t wait, such as broken glass or a sash that won’t close, ask about a temporary repair or a board-up to secure the opening while the new window is on order.
Step 6: Getting the house ready
A little preparation makes install day go faster:
- Clear window sills and move furniture a few feet back from each window.
- Take down blinds, curtains and rods, or ask in advance whether the crew will.
- Make a path from the door to each window, and keep pets and children away from the work areas.
- If you have a security system, note which windows have sensors so they can be dealt with.
- Clear plants and outdoor furniture away from the outside of each window.
Step 7: Install day
For an insert
The installer removes the interior stops and the old sashes, along with any sash weights and pulleys, and cleans up the existing frame. The new unit is set on the sill, shimmed so it’s level, plumb and square, and fastened through its frame. The gaps between the new frame and the old one are filled with insulation suited to windows, typically a low-expansion foam or backer rod and sealant, so the frame isn’t bowed. Interior stops or trim go back on, and the exterior joint is sealed, sometimes with aluminum or vinyl capping over the old exterior trim.
For full-frame
Trim comes off inside and out, the old frame is removed, and the rough opening is checked and repaired if needed. The new window is installed and flashed into the wall’s weather barrier according to the manufacturer’s instructions, then insulated, trimmed and sealed. Full-frame work takes longer per opening.
In a pre-1978 home, unless testing has shown the paint being disturbed is free of lead-based paint, all of this happens inside lead-safe containment, with cleanup and cleaning verification before the area reopens. See our lead-safe window work guide.
Step 8: Cleanup and the walkthrough
Before the job is called finished, walk through each window with the installer:
- Open and close every sash fully. It should move smoothly and stay where you leave it.
- Lock every window and check that the lock pulls the sash tight.
- Tilt in any tilt-wash sashes to make sure they release and return correctly.
- Look at the interior and exterior seams for gaps in sealant or trim.
- Confirm screens are in place and that old windows and debris are gone.
Keep the window labels or the order paperwork. They record the NFRC ratings and product details you may want later.
Ready to start?
Call or text (614) 333-6302 or book online. You can also read more about window replacement in Columbus or our energy-efficient windows.
Frequently asked questions
Do I need to be home during the installation?
Someone should be there at the start to confirm which windows are being done and at the end for the walkthrough. Whether you stay in between is up to you, as long as the crew has access to every window inside and out.
What happens if rot is found after the old window comes out?
That’s one of the few surprises a replacement can bring, especially with full-frame work. A good quote says how hidden damage will be handled: the installer should stop, show you what was found, and price the repair before going ahead.
Can windows be replaced in winter?
Yes. Each opening is open to the weather only while its own window is being swapped, and the work moves one opening at a time. Very cold temperatures can affect some sealants and foams, so installers choose products rated for the conditions.
Does window replacement need a building permit in Ohio?
It depends on the scope of the job and on your local building department, which enforces the Residential Code of Ohio in its area. Cutting a new or larger opening, especially in a foundation wall, is structural work that typically needs plan approval. Ask your building department before work that changes an opening.
Call or text · Columbus, OH
Need window replacement?
(614) 333-6302- We measure before we quote
- Columbus-based · 55-mile service area
More guides
All guidesRepair or Replace? Signs It’s Time for New Windows
A window that bothers you is not automatically a window that needs replacing. Many of the problems that make a window feel worn out are part failures, and a part can be swapped for far less disruption than a whole unit.
Foggy Insulated Glass: Replace the Unit or the Whole Window?
If the frame and sash are sound, a new sealed glass unit gives you clear glass again without disturbing the trim, siding or plaster around the window. The decision gets harder when other parts of the window are wearing out too.
Pre-1978 Homes and Window Work: The EPA Lead-Safe Rules
If your home was built before 1978, paying someone to replace or repair its windows is regulated work. Windows are one of the places lead-based paint matters most, because sashes rub against painted frames every time they open and close.